PCG0501 Ball Screw
Series / Model PCG0501
Review PCG0501 ball screw dimensions: d = 5 mm, 1 mm lead and L = 15 mm. Compare the nut interface and request a drawing review.
Overview
PCG0501 is a PCG ball-screw catalog reference with d = 5 mm and I = 1 mm lead. This page supports a model-specific drawing and quotation review, with published dimensions and a comparison to PCG0502.
Fit a short threaded nut around a 5 mm screw
The 1 mm lead is the distinguishing motion choice for a compact threaded-nut layout. Reserve space for the retaining interface as well as the cylindrical body.
L = 15 mm versus 20 for PCG0502; B = 5 mm versus 6 for PCG0502; I = 1 mm versus 2 for PCG0502. These are catalog comparisons, not an interchangeability approval. Check the entire assembly whenever the screw or nut model changes.
PCG0501 dimensions and basic load ratings
| Drawing field | Value | Unit or notation |
|---|---|---|
| d | 5 | mm |
| I | 1 | mm |
| Da | 0.8 | mm |
| n | 3 | catalog circuit notation |
| Ca(N) | 500 | N |
| Coa(N) | 700 | N |
| D | 12 | mm |
| L | 15 | mm |
| B | 5 | mm |
| A | M10x1 | thread notation |
I denotes lead, Da denotes ball diameter and n is the catalog circuit notation. Keep n exactly as shown; it is not a thread-start count. Ca and Coa are basic dynamic and static load ratings in newtons. They are not a continuous operating-load limit or a promised service life.
Review the nut-to-carriage interface
The PCG drawing uses A for the nut mounting thread, listed here as M10x1, and B = 5 mm. The ground-section drawing uses T and L1 for corresponding callouts. Use the selected manufacturing variant and its controlled drawing when designing the mating thread, shoulder and retention.
The listed L dimension is the nut length, not the working stroke. Specify shaft length, end machining, bearing supports and end clearances separately. Mark the nut orientation and lubrication access in the assembly so that the mounting decision can be checked before ordering.
Confirm the duty before selecting the assembly
Use the 1 mm lead when translating the required linear travel into screw rotation. Lead alone does not establish achievable speed or positioning accuracy. Check screw length, support arrangement, rotational speed, acceleration, axial loading and required service life together.
Provide the external guide arrangement and any side loads or moments on the carriage. Review lubrication, seals and contamination protection for the actual installation. Confirm the raceway manufacturing method, accuracy and preload or clearance of the offered configuration; the catalog heading and model reference are not a stock, delivery or performance commitment.
Questions about PCG0501
How does PCG0501 differ from PCG0502?
L = 15 mm versus 20 for PCG0502; B = 5 mm versus 6 for PCG0502; I = 1 mm versus 2 for PCG0502. The 1 mm lead is the distinguishing motion choice for a compact threaded-nut layout. Reserve space for the retaining interface as well as the cylindrical body.
Is M10x1 the screw lead of PCG0501?
No. M10x1 is the nut mounting-thread notation in the selected PCG table. The screw lead is I = 1 mm. Keep the mounting thread, shaft diameter and motion lead as separate requirements.
Does PCG0501 guarantee a particular accuracy or preload?
The model identifies a catalog configuration. Confirm the complete designation, raceway manufacturing method, accuracy class, axial clearance or preload and inspection conditions in the quotation. A model prefix alone does not establish these properties.
What should I send for a PCG0501 quotation?
Specify PCG0501, quantity, working stroke, total shaft length, end-machining drawing, mounting arrangement, axial load cycle, travel speed, acceleration, required life and accuracy. Include lubrication access and the operating environment, and request confirmation of the offered drawing revision.
Request the PCG0501 drawing and configuration
Review the complete ball-screw family tables and drawings for the original notation. Send your layout and duty information through the PCG0501 inquiry page. Ask the quotation to identify the exact assembly, shaft ends, drawing revision and inspection requirements.
Need help selecting a model or configuration?
This page is a catalog reference. Send the exact model, drawing and load cycle to confirm the offered configuration and commercial terms.
