Products

Home›Products

PCG0601 Ball Screw
Ball Screw Catalog Models

PCG0601 Ball Screw

Series / Model PCG0601

Review PCG0601 ball screw dimensions: d = 6 mm, 1 mm lead and L = 20 mm. Compare the nut interface and request a drawing review.

Product information

Overview

PCG0601 is a PCG ball-screw catalog reference with d = 6 mm and I = 1 mm lead. This page supports a model-specific drawing and quotation review, with published dimensions and a comparison to PCG0501.

Retain 1 mm lead while moving to a 6 mm screw

The shaft diameter changes without a change to the M10x1 thread designation. A threaded bracket alone cannot identify the screw size or verify the bearing-end drawing.

d = 6 mm versus 5 for PCG0501; L = 20 mm versus 15 for PCG0501; B = 6 mm versus 5 for PCG0501. These are catalog comparisons, not an interchangeability approval. Check the entire assembly whenever the screw or nut model changes.

PCG0601 dimensions and basic load ratings

PCG0601 catalog reference, Series Ball Screw, printed page 4
Drawing field Value Unit or notation
d 6 mm
I 1 mm
Da 0.8 mm
n 3 catalog circuit notation
Ca(N) 560 N
Coa(N) 950 N
D 12 mm
L 20 mm
B 6 mm
A M10x1 thread notation

I denotes lead, Da denotes ball diameter and n is the catalog circuit notation. Keep n exactly as shown; it is not a thread-start count. Ca and Coa are basic dynamic and static load ratings in newtons. They are not a continuous operating-load limit or a promised service life.

Review the nut-to-carriage interface

The PCG drawing uses A for the nut mounting thread, listed here as M10x1, and B = 6 mm. The ground-section drawing uses T and L1 for corresponding callouts. Use the selected manufacturing variant and its controlled drawing when designing the mating thread, shoulder and retention.

The listed L dimension is the nut length, not the working stroke. Specify shaft length, end machining, bearing supports and end clearances separately. Mark the nut orientation and lubrication access in the assembly so that the mounting decision can be checked before ordering.

Confirm the duty before selecting the assembly

Use the 1 mm lead when translating the required linear travel into screw rotation. Lead alone does not establish achievable speed or positioning accuracy. Check screw length, support arrangement, rotational speed, acceleration, axial loading and required service life together.

Provide the external guide arrangement and any side loads or moments on the carriage. Review lubrication, seals and contamination protection for the actual installation. Confirm the raceway manufacturing method, accuracy and preload or clearance of the offered configuration; the catalog heading and model reference are not a stock, delivery or performance commitment.

Questions about PCG0601

How does PCG0601 differ from PCG0501?

d = 6 mm versus 5 for PCG0501; L = 20 mm versus 15 for PCG0501; B = 6 mm versus 5 for PCG0501. The shaft diameter changes without a change to the M10x1 thread designation. A threaded bracket alone cannot identify the screw size or verify the bearing-end drawing.

Is M10x1 the screw lead of PCG0601?

No. M10x1 is the nut mounting-thread notation in the selected PCG table. The screw lead is I = 1 mm. Keep the mounting thread, shaft diameter and motion lead as separate requirements.

Does PCG0601 guarantee a particular accuracy or preload?

The model identifies a catalog configuration. Confirm the complete designation, raceway manufacturing method, accuracy class, axial clearance or preload and inspection conditions in the quotation. A model prefix alone does not establish these properties.

What should I send for a PCG0601 quotation?

Specify PCG0601, quantity, working stroke, total shaft length, end-machining drawing, mounting arrangement, axial load cycle, travel speed, acceleration, required life and accuracy. Include lubrication access and the operating environment, and request confirmation of the offered drawing revision.

Request the PCG0601 drawing and configuration

Review the complete ball-screw family tables and drawings for the original notation. Send your layout and duty information through the PCG0601 inquiry page. Ask the quotation to identify the exact assembly, shaft ends, drawing revision and inspection requirements.

Custom requirements

Need help selecting a model or configuration?

This page is a catalog reference. Send the exact model, drawing and load cycle to confirm the offered configuration and commercial terms.

Discuss your application
Product inquiry

Request a quote or engineering review