Products

Home›Products

PFI1202 Ball Screw
Ball Screw Catalog Models

PFI1202 Ball Screw

Series / Model PFI1202

Review PFI1202 ball screw dimensions: d = 11.5 mm, 2 mm lead and L = 30 mm. Compare the nut interface and request a drawing review.

Product information

Overview

PFI1202 is a PFI ball-screw catalog reference with d = 11.5 mm and I = 2 mm lead. This page supports a model-specific drawing and quotation review, with published dimensions and a comparison to PFI1003.

Check the 44 mm flange around an 11.5 mm screw

The 2 mm lead configuration combines an 11.5 mm shaft value with a wider flange than PFI1003. Review the flange and end-bearing arrangement separately instead of selecting by nominal model group.

d = 11.5 mm versus 9.5 for PFI1003; I = 2 mm versus 3 for PFI1003; A = 44 mm versus 38 for PFI1003; L = 30 mm versus 28 for PFI1003; W = 32 mm versus 28 for PFI1003. These are catalog comparisons, not an interchangeability approval. Check the entire assembly whenever the screw or nut model changes.

PFI1202 dimensions and basic load ratings

PFI1202 catalog reference, Series Ball Screw, printed page 8
Drawing field Value Unit or notation
d 11.5 mm
I 2 mm
Da 1.588 mm
n 3 catalog circuit notation
Ca(N) 2840 N
Coa(N) 4440 N
D 20 mm
A 44 mm
B 8 mm
L 30 mm
W 32 mm

I denotes lead, Da denotes ball diameter and n is the catalog circuit notation. Keep n exactly as shown; it is not a thread-start count. Ca and Coa are basic dynamic and static load ratings in newtons. They are not a continuous operating-load limit or a promised service life.

Review the nut-to-carriage interface

The PFI drawing is a flanged-nut arrangement. Review D = 20 mm, flange callout A = 44 mm, B = 8 mm, L = 30 mm and W = 32 mm together. The table does not supply every bolt, counterbore, lubrication and mating-fit requirement. Select the correct flange view and confirm a controlled mounting drawing.

The listed L dimension is the nut length, not the working stroke. Specify shaft length, end machining, bearing supports and end clearances separately. Mark the nut orientation and lubrication access in the assembly so that the mounting decision can be checked before ordering.

Confirm the duty before selecting the assembly

Use the 2 mm lead when translating the required linear travel into screw rotation. Lead alone does not establish achievable speed or positioning accuracy. Check screw length, support arrangement, rotational speed, acceleration, axial loading and required service life together.

Provide the external guide arrangement and any side loads or moments on the carriage. Review lubrication, seals and contamination protection for the actual installation. Confirm the raceway manufacturing method, accuracy and preload or clearance of the offered configuration; the catalog heading and model reference are not a stock, delivery or performance commitment.

Questions about PFI1202

How does PFI1202 differ from PFI1003?

d = 11.5 mm versus 9.5 for PFI1003; I = 2 mm versus 3 for PFI1003; A = 44 mm versus 38 for PFI1003; L = 30 mm versus 28 for PFI1003; W = 32 mm versus 28 for PFI1003. The 2 mm lead configuration combines an 11.5 mm shaft value with a wider flange than PFI1003. Review the flange and end-bearing arrangement separately instead of selecting by nominal model group.

Can the PFI1202 flange be drilled from these table values alone?

No. A = 44 mm and W = 32 mm are reference callouts, not a complete manufacturing drawing. Confirm the offered flange view, hole pattern, fasteners and mating fits before drilling the bracket.

Does PFI1202 guarantee a particular accuracy or preload?

The model identifies a catalog configuration. Confirm the complete designation, raceway manufacturing method, accuracy class, axial clearance or preload and inspection conditions in the quotation. A model prefix alone does not establish these properties.

What should I send for a PFI1202 quotation?

Specify PFI1202, quantity, working stroke, total shaft length, end-machining drawing, mounting arrangement, axial load cycle, travel speed, acceleration, required life and accuracy. Include lubrication access and the operating environment, and request confirmation of the offered drawing revision.

Request the PFI1202 drawing and configuration

Review the complete ball-screw family tables and drawings for the original notation. Send your layout and duty information through the PFI1202 inquiry page. Ask the quotation to identify the exact assembly, shaft ends, drawing revision and inspection requirements.

Custom requirements

Need help selecting a model or configuration?

This page is a catalog reference. Send the exact model, drawing and load cycle to confirm the offered configuration and commercial terms.

Discuss your application
Product inquiry

Request a quote or engineering review