PFU1610 Rolled Ball Screw
Series / Model PFU1610
Review PFU1610 rolled ball screw dimensions: 15 mm shaft, 10 mm lead and 50 mm nut length. Compare mounting details and request engineering confirmation.
Overview
PFU1610 is a PFU reference in the catalog’s Stock Rolled Ball Screw section. Its row lists d = 15 mm, a 10 mm lead and L = 50 mm. Use this page to review the model’s geometry and prepare a configuration inquiry.
Separate lead from the mounting envelope
The 10 mm lead distinguishes this row from PFU1605 even though the listed external dimensions match. The source gives three circuits rather than four and a lower basic dynamic rating. If changing an existing 5 mm-lead design, review commanded travel per revolution and the load cycle separately from bracket dimensions.
PFU1610 catalog dimensions and ratings
| Parameter | Reference | Unit |
|---|---|---|
| Shaft d | 15 | mm |
| Lead I | 10 | mm/rev |
| Ball diameter Da | 3 | mm |
| Circuits n | 3 | count |
| Basic dynamic rating Ca | 7350 | N |
| Basic static rating Coa | 10860 | N |
| Nut body D | 28 | mm |
| Flange A | 48 | mm |
| B | 10 | mm |
| Nut length L | 50 | mm |
| W | 38 | mm |
| H | 40 | mm |
| Hole diameter X | 5.5 | mm |
Dimensions retain the source symbols and printed precision. I denotes lead, Da ball diameter and n the source number of circuits. Ca and Coa are basic dynamic and static ratings in newtons. Do not treat either rating as an allowable payload or a complete life calculation.
Compare PFU1610 with PFU1605
| Field | PFU1610 | PFU1605 |
|---|---|---|
| d | 15 | 15 |
| I | 10 | 5 |
| D | 28 | 28 |
| L | 50 | 50 |
| A | 48 | 48 |
The comparison uses separately verified catalog rows. Matching dimensions support an initial envelope review only. Different leads change travel per screw revolution, while the required rotational speed still depends on the target linear speed. Neither the table nor the model name establishes accuracy grade, preload or supplied configuration.
Installation and inquiry checklist
For the PFU flange, review A = 48 mm, W = 38 mm, H = 40 mm and X = 5.5 mm together. Confirm the applicable hole arrangement, angular orientation and bolt access against the controlled drawing. The family illustration is not a model-specific manufacturing drawing.
- Identify PFU1610, rolled process, quantity, working stroke and overall screw length. Attach the screw-end and nut-housing drawings.
- Provide axial force through the complete cycle, travel speed, acceleration, mounting orientation and required life. Review buckling and critical speed for the actual unsupported span.
- State positioning requirements, acceptable axial play, lubrication access and environmental protection. Confirm offered preload, accuracy and inspection conditions with engineering.
Allow for support bearings, end clearances and maintenance access beyond the listed nut length. Confirm the offered assembly and drawing revision before committing the machine layout.
Questions about PFU1610
Does PFU1610 specify the complete screw length?
No. The catalog lists L = 50 mm for the nut. Working stroke, screw length, end machining and support locations must be specified separately.
Can PFU1610 replace PFU1605 without a drawing check?
No. The comparison preserves each row’s d, lead, D, L and A values. Confirm the full mounting interface, shaft ends, load cycle and motion requirements; the catalog does not establish interchangeability.
What does the PFU1610 load table establish?
The source lists Ca = 7350 N and Coa = 10860 N as basic ratings. They are not permissible machine loads. Confirm the rating basis, duty cycle, life target and safety checks before selection.
Source and engineering confirmation
See the original ball screw catalog, PDF page 4 (printed page 3); the PFU header and drawing are on PDF page 3. These are catalog reference values. Engineering must confirm the exact offered dimensions, configuration and controlled drawing. The historical section title does not establish current stock, price or delivery.
Send the model and duty details through the PFU1610 configuration inquiry.
Need help selecting a model or configuration?
Catalog reference only. Confirm the offered assembly, controlled drawing, duty cycle and commercial terms.
