Products

Home›Products

PCG4005 Rolled Ball Screw
Ball Screw Catalog Models

PCG4005 Rolled Ball Screw

Series / Model PCG4005

Review PCG4005 rolled ball screw dimensions: 39.58 mm shaft, 5 mm lead and 55 mm nut length. Compare mounting details and request engineering confirmation.

Product information

Overview

PCG4005 is a PCG reference in the catalog’s Stock Rolled Ball Screw section. Its row lists d = 39.58 mm, a 5 mm lead and L = 55 mm. Use this page to review the model’s geometry and prepare a configuration inquiry.

Preserve the 39.58 mm shaft precision

The source prints d = 39.58 mm, not a rounded 40 mm value. This five-circuit entry has L = 55 mm and A = M60x2, while PCG4010 moves to M65x2. Carry the exact shaft and mounting callouts into the specification before comparing the two leads for an existing housing.

PCG4005 catalog dimensions and ratings

PCG4005 rolled catalog row, PDF page 6
Parameter Reference Unit
Shaft d 39.58 mm
Lead I 5 mm/rev
Ball diameter Da 3.5 mm
Circuits n 5 count
Basic dynamic rating Ca 22890 N
Basic static rating Coa 59450 N
Nut body D 65 mm
Nut length L 55 mm
B 27 mm
Mounting thread A M60x2 metric thread

Dimensions retain the source symbols and printed precision. I denotes lead, Da ball diameter and n the source number of circuits. Ca and Coa are basic dynamic and static ratings in newtons. Do not treat either rating as an allowable payload or a complete life calculation.

Compare PCG4005 with PCG4010

Verified catalog comparison; dimensions in mm; lead I in mm/rev; A may be a metric thread designation
Field PCG4005 PCG4010
d 39.58 39.51
I 5 10
D 65 68
L 55 95
A M60x2 M65x2

The comparison uses separately verified catalog rows. Matching dimensions support an initial envelope review only. Different leads change travel per screw revolution, while the required rotational speed still depends on the target linear speed. Neither the table nor the model name establishes accuracy grade, preload or supplied configuration.

Installation and inquiry checklist

For this PCG nut, A = M60x2 is the mounting-thread designation, not a flange diameter. Review it together with B = 27 mm, D = 65 mm and L = 55 mm. Confirm mating-thread tolerance, engagement, shoulder seating and locking method on the assembly drawing.

  • Identify PCG4005, rolled process, quantity, working stroke and overall screw length. Attach the screw-end and nut-housing drawings.
  • Provide axial force through the complete cycle, travel speed, acceleration, mounting orientation and required life. Review buckling and critical speed for the actual unsupported span.
  • State positioning requirements, acceptable axial play, lubrication access and environmental protection. Confirm offered preload, accuracy and inspection conditions with engineering.

Allow for support bearings, end clearances and maintenance access beyond the listed nut length. Confirm the offered assembly and drawing revision before committing the machine layout.

Questions about PCG4005

Does PCG4005 specify the complete screw length?

No. The catalog lists L = 55 mm for the nut. Working stroke, screw length, end machining and support locations must be specified separately.

Can PCG4005 replace PCG4010 without a drawing check?

No. The comparison preserves each row’s d, lead, D, L and A values. Confirm the full mounting interface, shaft ends, load cycle and motion requirements; the catalog does not establish interchangeability.

What does the PCG4005 load table establish?

The source lists Ca = 22890 N and Coa = 59450 N as basic ratings. They are not permissible machine loads. Confirm the rating basis, duty cycle, life target and safety checks before selection.

Source and engineering confirmation

See the original ball screw catalog, PDF page 6 (printed page 5); the PCG header and drawing are on PDF page 5. These are catalog reference values. Engineering must confirm the exact offered dimensions, configuration and controlled drawing. The historical section title does not establish current stock, price or delivery.

Send the model and duty details through the PCG4005 configuration inquiry.

Custom requirements

Need help selecting a model or configuration?

Catalog reference only. Confirm the offered assembly, controlled drawing, duty cycle and commercial terms.

Discuss your application
Product inquiry

Request a quote or engineering review