Products

Home›Products

PCG0801 Ground Ball Screw
Ball Screw Catalog Models

PCG0801 Ground Ball Screw

Series / Model PCG0801

Review PCG0801 ground ball screw catalog dimensions: 8 mm screw reference, 1 mm lead and 22 mm nut length. Confirm the assembly drawing.

Product information

Overview

PCG0801 is a PCG ground ball screw catalog reference with d = 8 mm, I = 1 mm lead and L = 22 mm nut length. This page follows the “Stock Ground Ball Screw” section of the Series Ball Screw catalog, printed page 16 (PDF page 17). The heading identifies the catalog section, not current inventory or an offered accuracy grade.

PCG0801: the mounting decision

This 1 mm lead configuration needs a speed review for the required travel rate, alongside clearance for its threaded retention interface.

PCG0801 lists I = 1 mm/rev; PCG0802 lists I = 2 mm/rev. PCG0801 lists L = 22 mm; PCG0802 lists L = 27 mm. PCG0801 lists Da = 0.8 mm; PCG0802 lists Da = 1.2 mm. PCG0801 lists Ca = 650 N; PCG0802 lists Ca = 1300 N. This comparison uses ground-section rows. Confirm the process and approved drawing before substitution.

PCG0801 ground catalog dimensions

PCG0801, ground process, printed page 16
Field Value Unit or notation
d 8 mm
I 1 mm/rev
Da 0.8 mm
D 16 mm
L 22 mm
L1 8 mm
T M14x1 thread notation
n 3 source circuit notation
Ca 650 N
Coa 1300 N

I denotes lead in millimetres per revolution, Da ball diameter and n the source circuit notation. The n value is not a thread-start count. Dimensions retain the source precision. Ca and Coa are basic load ratings, not a guaranteed operating load or service life.

Review the PCG interface

The PCG ground drawing uses T for the nut mounting thread and L1 for the associated axial callout. For PCG0801, T = M14x1, L1 = 8 mm and D = 16 mm. Check the mating thread, shoulder contact and retention access as one interface. Preserve these ground-section symbols rather than translating them into labels from another process table.

Nut length is separate from working stroke and total shaft length. Add the end bearings, end machining and clearance at both travel limits to the assembly layout. Check installation and lubrication access in the carriage.

Engineering review checklist

  • Identify PCG0801, ground process and the required drawing revision in the inquiry.
  • Provide stroke, shaft length, support arrangement and shaft-end details.
  • State axial load over the cycle, speed, acceleration and desired service life.
  • Define positioning requirements, clearance or preload, lubrication and contamination protection.

Use the 1 mm lead to relate linear travel to screw rotation, then check rotational limits for the actual supported length. Check critical speed, buckling, installed accuracy, guides and carriage moments for the complete assembly.

Questions about ground PCG0801

How does ground PCG0801 compare with PCG0802?

PCG0801 lists I = 1 mm/rev; PCG0802 lists I = 2 mm/rev. PCG0801 lists L = 22 mm; PCG0802 lists L = 27 mm. PCG0801 lists Da = 0.8 mm; PCG0802 lists Da = 1.2 mm. PCG0801 lists Ca = 650 N; PCG0802 lists Ca = 1300 N. Use the exact row and process when reviewing the assembly; these differences are not a substitution approval.

Is M14x1 the motion lead of PCG0801?

No. T = M14x1 is the mounting-thread notation. The ball-screw lead is I = 1 mm. Keep mounting-thread fit and travel per revolution as separate requirements in the drawing review.

What does the PCG0801 load rating mean?

Ca = 650 N and Coa = 1300 N are the catalog basic dynamic and static ratings. They do not specify a permissible continuous operating load. Review the load cycle, support system and required life for the complete assembly.

Request the controlled drawing

Use the ground ball screw family reference and the original catalog, PDF page 17. Send your layout through the PCG0801 ground configuration inquiry. Ask for an approved assembly drawing and confirmation of inspection requirements before releasing the design.

Custom requirements

Need help selecting a model or configuration?

Catalog reference only. Confirm the offered assembly and approved drawing.

Discuss your application
Product inquiry

Request a quote or engineering review