PCI1205 Ground Ball Screw
Series / Model PCI1205
Review PCI1205 ground ball screw catalog dimensions: 12 mm screw reference, 5 mm lead and 30 mm nut length. Confirm the assembly drawing.
Overview
PCI1205 is a PCI ground ball screw catalog reference with d = 12 mm, I = 5 mm lead and L = 30 mm nut length. This page follows the “Stock Ground Ball Screw” section of the Series Ball Screw catalog, printed page 17 (PDF page 18). The heading identifies the catalog section, not current inventory or an offered accuracy grade.
PCI1205: the mounting decision
This row has a shorter nut than PCI1204 while retaining the same listed body diameter and basic ratings. The lead still changes the motion ratio.
PCI1205 lists I = 5 mm/rev; PCI1204 lists I = 4 mm/rev. PCI1205 lists L = 30 mm; PCI1204 lists L = 40 mm. PCI1205 lists Da = 2.5 mm; PCI1204 lists Da = 2.381 mm. PCI1205 lists n = 3; PCI1204 lists n = 4. This comparison uses ground-section rows. Confirm the process and approved drawing before substitution.
PCI1205 ground catalog dimensions
| Field | Value | Unit or notation |
|---|---|---|
| d | 12 | mm |
| I | 5 | mm/rev |
| Da | 2.5 | mm |
| L | 30 | mm |
| D | 24 | mm |
| n | 3 | source circuit notation |
| Ca | 4400 | N |
| Coa | 9000 | N |
I denotes lead in millimetres per revolution, Da ball diameter and n the source circuit notation. The n value is not a thread-start count. Dimensions retain the source precision. Ca and Coa are basic load ratings, not a guaranteed operating load or service life.
Review the PCI interface
The PCI drawing shows a cylindrical nut with additional retaining and lubrication features. The table establishes D = 24 mm and L = 30 mm, but does not give numerical values for every illustrated callout. Request L1, L2, L3, D1, M and R as applicable on the approved drawing. Do not estimate these features from the image when designing a housing or anti-rotation detail.
Nut length is separate from working stroke and total shaft length. Add the end bearings, end machining and clearance at both travel limits to the assembly layout. Check installation and lubrication access in the carriage.
Engineering review checklist
- Identify PCI1205, ground process and the required drawing revision in the inquiry.
- Provide stroke, shaft length, support arrangement and shaft-end details.
- State axial load over the cycle, speed, acceleration and desired service life.
- Define positioning requirements, clearance or preload, lubrication and contamination protection.
Use the 5 mm lead to relate linear travel to screw rotation, then check rotational limits for the actual supported length. Check critical speed, buckling, installed accuracy, guides and carriage moments for the complete assembly.
Questions about ground PCI1205
How does ground PCI1205 compare with PCI1204?
PCI1205 lists I = 5 mm/rev; PCI1204 lists I = 4 mm/rev. PCI1205 lists L = 30 mm; PCI1204 lists L = 40 mm. PCI1205 lists Da = 2.5 mm; PCI1204 lists Da = 2.381 mm. PCI1205 lists n = 3; PCI1204 lists n = 4. Use the exact row and process when reviewing the assembly; these differences are not a substitution approval.
Are D = 24 mm and L = 30 mm enough to manufacture a PCI1205 housing?
No. They define only part of the catalog envelope. Confirm the retaining features, lubrication connection, tolerances and orientation on the approved assembly drawing before machining.
What does the PCI1205 load rating mean?
Ca = 4400 N and Coa = 9000 N are the catalog basic dynamic and static ratings. They do not specify a permissible continuous operating load. Review the load cycle, support system and required life for the complete assembly.
Request the controlled drawing
Use the ground ball screw family reference and the original catalog, PDF page 18. Send your layout through the PCI1205 ground configuration inquiry. Ask for an approved assembly drawing and confirmation of inspection requirements before releasing the design.
Need help selecting a model or configuration?
Catalog reference only. Confirm the offered assembly and approved drawing.
