Products

Home›Products

PFI4020 Rolled Ball Screw
Ball Screw Catalog Models

PFI4020 Rolled Ball Screw

Series / Model PFI4020

Review PFI4020 rolled ball screw dimensions, 20 mm lead and 90 mm nut length. Compare the PFI flange envelope and request a configuration drawing.

Product information

Overview

PFI4020 is a PFI flanged-nut reference in the rolled section of the Series Motion ball screw catalog. Its source row lists d = 38 mm and I = 20 mm per revolution. Use this page to compare the mounting envelope and prepare a drawing-based configuration inquiry.

Do not infer the shaft dimension from the 40-series code

PFI4020 lists d = 38 mm, a 20 mm lead and three circuits. PFI4040 instead lists d = 40 mm, a 40 mm lead and two circuits. The larger-lead model has a shorter nut but a larger body and flange envelope, so this comparison needs both axial and radial clearance checks.

PFI4020 dimensions and basic ratings

PFI4020 rolled reference, catalog PDF page 10; units shown for each field
Parameter Reference Unit
Shaft callout d 38 mm
Lead I 20 mm/rev
Ball diameter Da 6 mm
Number of circuits n 3 count
Basic dynamic rating Ca 29330 N
Basic static rating Coa 56390 N
Nut body callout D 64 mm
Flange callout A 106 mm
Drawing callout B 18 mm
Nut length L 90 mm
Drawing callout W 81 mm

Values retain the printed precision and source symbols. The circuit count n is dimensionless; it is not a thread-start count. Drawing callouts A, B and W belong to the PFI flange geometry, not a nut mounting-thread designation. Check the original drawing on PDF page 9 for the callout positions. Hole details and the offered flange form must be confirmed on the controlled drawing rather than inferred from this table.

Compare PFI4020 with PFI4040

PFI catalog comparison: d, D, A, B, L and W in mm; I in mm/rev
Field PFI4020 PFI4040
d 38 40
I 20 40
D 64 68
A 106 110
B 18 18
L 90 70
W 81 85

Use the complete selected row. Shared dimensions do not establish interchangeability, equivalent preload, accuracy or load performance. Check the nut seat, flange retention, shaft-end geometry and lubrication access together before replacing an assembly or releasing a new design.

Information needed for configuration review

  • Specify PFI4020, rolled process, quantity, required working stroke and overall screw length. Include the mating flange, nut-housing and shaft-end drawings.
  • Provide the axial load through each movement, speed, acceleration, mounting direction, cycles per hour and required service life. State the support arrangement and unsupported screw length.
  • Identify positioning requirements, permitted axial play, lubrication access and environmental conditions. Request the offered accuracy, preload, inspection basis and drawing revision in the quotation.

Catalog inclusion is not confirmation of current stock or an approved application. Confirm the offered configuration, availability and delivery before finalizing the machine layout. Basic ratings are not a substitute for an application-specific selection calculation.

Questions about PFI4020

Is PFI4020 a rolled or ground catalog reference?

This PFI4020 row appears in the Stock Rolled Ball Screw section, on PDF page 10. The PFI prefix is a family label; do not infer process or accuracy from the prefix alone. Confirm the offered process and accuracy on the configuration drawing and quotation.

Does L = 90 mm specify the working stroke?

No. L = 90 mm is the catalog nut length. Required stroke, overall screw length, shaft-end machining and support positions must be supplied separately.

Can the PFI4020 basic ratings be used as the machine working load?

Not directly. Ca = 29330 N and Coa = 56390 N are the printed basic dynamic and static ratings. Selection requires the load cycle, rating basis, target life and separate static, buckling and speed checks.

Check the source and request a drawing

Read the original PFI4020 catalog row and the PFI drawing and field definitions on PDF page 9. The 40 mm size table provides other catalog references. Send a PFI4020 rolled configuration inquiry with the application cycle and mounting requirements.

Custom requirements

Need help selecting a model or configuration?

Discuss your application
Product inquiry

Request a quote or engineering review