PFI5005 Rolled Ball Screw
Series / Model PFI5005
Review PFI5005 rolled ball screw dimensions, 5 mm lead and 52 mm nut length. Compare the PFI flange envelope and request a configuration drawing.
Overview
PFI5005 is a PFI flanged-nut reference in the rolled section of the Series Motion ball screw catalog. Its source row lists d = 49 mm and I = 5 mm per revolution. Use this page to compare the mounting envelope and prepare a drawing-based configuration inquiry.
Keep the five-circuit row distinct
PFI5005 is listed with five circuits, a 5 mm lead and a 52 mm nut length. The adjacent PFI5010 row has four circuits and a 93 mm nut length. Circuit count is not a count of thread starts, and it does not by itself establish life or allowable operating load. Preserve the complete catalog row for the selection review.
PFI5005 dimensions and basic ratings
| Parameter | Reference | Unit |
|---|---|---|
| Shaft callout d | 49 | mm |
| Lead I | 5 | mm/rev |
| Ball diameter Da | 3.5 | mm |
| Number of circuits n | 5 | count |
| Basic dynamic rating Ca | 24940 | N |
| Basic static rating Coa | 73960 | N |
| Nut body callout D | 68 | mm |
| Flange callout A | 110 | mm |
| Drawing callout B | 18 | mm |
| Nut length L | 52 | mm |
| Drawing callout W | 85 | mm |
Values retain the printed precision and source symbols. The circuit count n is dimensionless; it is not a thread-start count. Drawing callouts A, B and W belong to the PFI flange geometry, not a nut mounting-thread designation. Check the original drawing on PDF page 9 for the callout positions. Hole details and the offered flange form must be confirmed on the controlled drawing rather than inferred from this table.
Compare PFI5005 with PFI5010
| Field | PFI5005 | PFI5010 |
|---|---|---|
| d | 49 | 49.31 |
| I | 5 | 10 |
| D | 68 | 72 |
| A | 110 | 114 |
| B | 18 | 18 |
| L | 52 | 93 |
| W | 85 | 92 |
Use the complete selected row. Shared dimensions do not establish interchangeability, equivalent preload, accuracy or load performance. Check the nut seat, flange retention, shaft-end geometry and lubrication access together before replacing an assembly or releasing a new design.
Information needed for configuration review
- Specify PFI5005, rolled process, quantity, required working stroke and overall screw length. Include the mating flange, nut-housing and shaft-end drawings.
- Provide the axial load through each movement, speed, acceleration, mounting direction, cycles per hour and required service life. State the support arrangement and unsupported screw length.
- Identify positioning requirements, permitted axial play, lubrication access and environmental conditions. Request the offered accuracy, preload, inspection basis and drawing revision in the quotation.
Catalog inclusion is not confirmation of current stock or an approved application. Confirm the offered configuration, availability and delivery before finalizing the machine layout. Basic ratings are not a substitute for an application-specific selection calculation.
Questions about PFI5005
Is PFI5005 a rolled or ground catalog reference?
This PFI5005 row appears in the Stock Rolled Ball Screw section, on PDF page 10. The PFI prefix is a family label; do not infer process or accuracy from the prefix alone. Confirm the offered process and accuracy on the configuration drawing and quotation.
Does L = 52 mm specify the working stroke?
No. L = 52 mm is the catalog nut length. Required stroke, overall screw length, shaft-end machining and support positions must be supplied separately.
Can the PFI5005 basic ratings be used as the machine working load?
Not directly. Ca = 24940 N and Coa = 73960 N are the printed basic dynamic and static ratings. Selection requires the load cycle, rating basis, target life and separate static, buckling and speed checks.
Check the source and request a drawing
Read the original PFI5005 catalog row and the PFI drawing and field definitions on PDF page 9. The 50 mm size table provides other catalog references. Send a PFI5005 rolled configuration inquiry with the application cycle and mounting requirements.
