Products

Home›Products

PFI6320 Rolled Ball Screw
Ball Screw Catalog Models

PFI6320 Rolled Ball Screw

Series / Model PFI6320

Review PFI6320 rolled ball screw dimensions, 20 mm lead and 149 mm nut length. Compare the PFI flange envelope and request a configuration drawing.

Product information

Overview

PFI6320 is a PFI flanged-nut reference in the rolled section of the Series Motion ball screw catalog. Its source row lists d = 62.55 mm and I = 20 mm per revolution. Use this page to compare the mounting envelope and prepare a drawing-based configuration inquiry.

Reserve the 149 mm nut envelope

PFI6320 uses D = 95 mm, A = 146 mm and L = 149 mm. Compared with PFI6310, its ball diameter and basic ratings also change. The larger rating figures do not remove the need to check buckling, critical speed, support conditions and the actual load cycle for the complete screw assembly.

PFI6320 dimensions and basic ratings

PFI6320 rolled reference, catalog PDF page 10; units shown for each field
Parameter Reference Unit
Shaft callout d 62.55 mm
Lead I 20 mm/rev
Ball diameter Da 9.525 mm
Number of circuits n 4 count
Basic dynamic rating Ca 86590 N
Basic static rating Coa 191440 N
Nut body callout D 95 mm
Flange callout A 146 mm
Drawing callout B 22 mm
Nut length L 149 mm
Drawing callout W 116 mm

Values retain the printed precision and source symbols. The circuit count n is dimensionless; it is not a thread-start count. Drawing callouts A, B and W belong to the PFI flange geometry, not a nut mounting-thread designation. Check the original drawing on PDF page 9 for the callout positions. Hole details and the offered flange form must be confirmed on the controlled drawing rather than inferred from this table.

Compare PFI6320 with PFI6310

PFI catalog comparison: d, D, A, B, L and W in mm; I in mm/rev
Field PFI6320 PFI6310
d 62.55 62.55
I 20 10
D 95 85
A 146 131
B 22 22
L 149 98
W 116 107

Use the complete selected row. Shared dimensions do not establish interchangeability, equivalent preload, accuracy or load performance. Check the nut seat, flange retention, shaft-end geometry and lubrication access together before replacing an assembly or releasing a new design.

Information needed for configuration review

  • Specify PFI6320, rolled process, quantity, required working stroke and overall screw length. Include the mating flange, nut-housing and shaft-end drawings.
  • Provide the axial load through each movement, speed, acceleration, mounting direction, cycles per hour and required service life. State the support arrangement and unsupported screw length.
  • Identify positioning requirements, permitted axial play, lubrication access and environmental conditions. Request the offered accuracy, preload, inspection basis and drawing revision in the quotation.

Catalog inclusion is not confirmation of current stock or an approved application. Confirm the offered configuration, availability and delivery before finalizing the machine layout. Basic ratings are not a substitute for an application-specific selection calculation.

Questions about PFI6320

Is PFI6320 a rolled or ground catalog reference?

This PFI6320 row appears in the Stock Rolled Ball Screw section, on PDF page 10. The PFI prefix is a family label; do not infer process or accuracy from the prefix alone. Confirm the offered process and accuracy on the configuration drawing and quotation.

Does L = 149 mm specify the working stroke?

No. L = 149 mm is the catalog nut length. Required stroke, overall screw length, shaft-end machining and support positions must be supplied separately.

Can the PFI6320 basic ratings be used as the machine working load?

Not directly. Ca = 86590 N and Coa = 191440 N are the printed basic dynamic and static ratings. Selection requires the load cycle, rating basis, target life and separate static, buckling and speed checks.

Check the source and request a drawing

Read the original PFI6320 catalog row and the PFI drawing and field definitions on PDF page 9. The 63 mm size table provides other catalog references. Send a PFI6320 rolled configuration inquiry with the application cycle and mounting requirements.

Custom requirements

Need help selecting a model or configuration?

Discuss your application
Product inquiry

Request a quote or engineering review