Products

Home›Products

PFI8010 Rolled Ball Screw
Ball Screw Catalog Models

PFI8010 Rolled Ball Screw

Series / Model PFI8010

Review PFI8010 rolled ball screw dimensions, 10 mm lead and 98 mm nut length. Compare the PFI flange envelope and request a configuration drawing.

Product information

Overview

PFI8010 is a PFI flanged-nut reference in the rolled section of the Series Motion ball screw catalog. Its source row lists d = 80 mm and I = 10 mm per revolution. Use this page to compare the mounting envelope and prepare a drawing-based configuration inquiry.

Check the 98 mm nut before selecting the 20 mm-lead alternative

PFI8010 lists d = 80 mm and L = 98 mm. The PFI8020 shaft callout is also 80 mm, but its nut length is 160 mm and its body and flange callouts are larger. Do not carry a housing layout from the 10 mm-lead row into the 20 mm-lead design without a new interface check.

PFI8010 dimensions and basic ratings

PFI8010 rolled reference, catalog PDF page 10; units shown for each field
Parameter Reference Unit
Shaft callout d 80 mm
Lead I 10 mm/rev
Ball diameter Da 7.144 mm
Number of circuits n 4 count
Basic dynamic rating Ca 67160 N
Basic static rating Coa 192240 N
Nut body callout D 105 mm
Flange callout A 150 mm
Drawing callout B 22 mm
Nut length L 98 mm
Drawing callout W 127 mm

Values retain the printed precision and source symbols. The circuit count n is dimensionless; it is not a thread-start count. Drawing callouts A, B and W belong to the PFI flange geometry, not a nut mounting-thread designation. Check the original drawing on PDF page 9 for the callout positions. Hole details and the offered flange form must be confirmed on the controlled drawing rather than inferred from this table.

Compare PFI8010 with PFI8020

PFI catalog comparison: d, D, A, B, L and W in mm; I in mm/rev
Field PFI8010 PFI8020
d 80 80
I 10 20
D 105 125
A 150 170
B 22 22
L 98 160
W 127 145

Use the complete selected row. Shared dimensions do not establish interchangeability, equivalent preload, accuracy or load performance. Check the nut seat, flange retention, shaft-end geometry and lubrication access together before replacing an assembly or releasing a new design.

Information needed for configuration review

  • Specify PFI8010, rolled process, quantity, required working stroke and overall screw length. Include the mating flange, nut-housing and shaft-end drawings.
  • Provide the axial load through each movement, speed, acceleration, mounting direction, cycles per hour and required service life. State the support arrangement and unsupported screw length.
  • Identify positioning requirements, permitted axial play, lubrication access and environmental conditions. Request the offered accuracy, preload, inspection basis and drawing revision in the quotation.

Catalog inclusion is not confirmation of current stock or an approved application. Confirm the offered configuration, availability and delivery before finalizing the machine layout. Basic ratings are not a substitute for an application-specific selection calculation.

Questions about PFI8010

Is PFI8010 a rolled or ground catalog reference?

This PFI8010 row appears in the Stock Rolled Ball Screw section, on PDF page 10. The PFI prefix is a family label; do not infer process or accuracy from the prefix alone. Confirm the offered process and accuracy on the configuration drawing and quotation.

Does L = 98 mm specify the working stroke?

No. L = 98 mm is the catalog nut length. Required stroke, overall screw length, shaft-end machining and support positions must be supplied separately.

Can the PFI8010 basic ratings be used as the machine working load?

Not directly. Ca = 67160 N and Coa = 192240 N are the printed basic dynamic and static ratings. Selection requires the load cycle, rating basis, target life and separate static, buckling and speed checks.

Check the source and request a drawing

Read the original PFI8010 catalog row and the PFI drawing and field definitions on PDF page 9. The 80 mm size table provides other catalog references. Send a PFI8010 rolled configuration inquiry with the application cycle and mounting requirements.

Custom requirements

Need help selecting a model or configuration?

Discuss your application
Product inquiry

Request a quote or engineering review