Products

Home›Products

PCG3210 Rolled Ball Screw
Ball Screw Catalog Models

PCG3210 Rolled Ball Screw

Series / Model PCG3210

Review PCG3210 rolled ball screw dimensions: 31.6 mm shaft, 10 mm lead and 88 mm nut length. Compare mounting details and request engineering confirmation.

Product information

Overview

PCG3210 is a PCG reference in the catalog’s Stock Rolled Ball Screw section. Its row lists d = 31.6 mm, a 10 mm lead and L = 88 mm. Use this page to review the model’s geometry and prepare a configuration inquiry.

Keep the 31.6 mm PCG shaft value

PCG3210 prints d = 31.6 mm and Da = 5.556 mm, with three circuits. The PFU3210 entry instead prints d = 32 mm and larger balls, making the family prefix essential to identification. For this PCG row, the mounting callout is M55x1.5 and the nut length is 88 mm.

PCG3210 catalog dimensions and ratings

PCG3210 rolled catalog row, PDF page 6
Parameter Reference Unit
Shaft d 31.6 mm
Lead I 10 mm/rev
Ball diameter Da 5.556 mm
Circuits n 3 count
Basic dynamic rating Ca 23430 N
Basic static rating Coa 40700 N
Nut body D 60 mm
Nut length L 88 mm
B 25 mm
Mounting thread A M55x1.5 metric thread

Dimensions retain the source symbols and printed precision. I denotes lead, Da ball diameter and n the source number of circuits. Ca and Coa are basic dynamic and static ratings in newtons. Do not treat either rating as an allowable payload or a complete life calculation.

Compare PCG3210 with PCG3205

Verified catalog comparison; dimensions in mm; lead I in mm/rev; A may be a metric thread designation
Field PCG3210 PCG3205
d 31.6 31.6
I 10 5
D 60 55
L 88 63
A M55x1.5 M50x1.5

The comparison uses separately verified catalog rows. Matching dimensions support an initial envelope review only. Different leads change travel per screw revolution, while the required rotational speed still depends on the target linear speed. Neither the table nor the model name establishes accuracy grade, preload or supplied configuration.

Installation and inquiry checklist

For this PCG nut, A = M55x1.5 is the mounting-thread designation, not a flange diameter. Review it together with B = 25 mm, D = 60 mm and L = 88 mm. Confirm mating-thread tolerance, engagement, shoulder seating and locking method on the assembly drawing.

  • Identify PCG3210, rolled process, quantity, working stroke and overall screw length. Attach the screw-end and nut-housing drawings.
  • Provide axial force through the complete cycle, travel speed, acceleration, mounting orientation and required life. Review buckling and critical speed for the actual unsupported span.
  • State positioning requirements, acceptable axial play, lubrication access and environmental protection. Confirm offered preload, accuracy and inspection conditions with engineering.

Allow for support bearings, end clearances and maintenance access beyond the listed nut length. Confirm the offered assembly and drawing revision before committing the machine layout.

Questions about PCG3210

Does PCG3210 specify the complete screw length?

No. The catalog lists L = 88 mm for the nut. Working stroke, screw length, end machining and support locations must be specified separately.

Can PCG3210 replace PCG3205 without a drawing check?

No. The comparison preserves each row’s d, lead, D, L and A values. Confirm the full mounting interface, shaft ends, load cycle and motion requirements; the catalog does not establish interchangeability.

What does the PCG3210 load table establish?

The source lists Ca = 23430 N and Coa = 40700 N as basic ratings. They are not permissible machine loads. Confirm the rating basis, duty cycle, life target and safety checks before selection.

Source and engineering confirmation

See the original ball screw catalog, PDF page 6 (printed page 5); the PCG header and drawing are on PDF page 5. These are catalog reference values. Engineering must confirm the exact offered dimensions, configuration and controlled drawing. The historical section title does not establish current stock, price or delivery.

Send the model and duty details through the PCG3210 configuration inquiry.

Custom requirements

Need help selecting a model or configuration?

Catalog reference only. Confirm the offered assembly, controlled drawing, duty cycle and commercial terms.

Discuss your application
Product inquiry

Request a quote or engineering review