Products

Home›Products

PCG3232 Rolled Ball Screw
Ball Screw Catalog Models

PCG3232 Rolled Ball Screw

Series / Model PCG3232

Review PCG3232 rolled ball screw dimensions: 31 mm shaft, 32 mm lead and 60 mm nut length. Compare mounting details and request engineering confirmation.

Product information

Overview

PCG3232 is a PCG reference in the catalog’s Stock Rolled Ball Screw section. Its row lists d = 31 mm, a 32 mm lead and L = 60 mm. Use this page to review the model’s geometry and prepare a configuration inquiry.

Separate the 60 mm nut from PCG3220

PCG3232 uses the same M56x1.5 thread and 62 mm body dimension as PCG3220, while L decreases from 95 to 60 mm. Its 32 mm lead and two circuits are distinct selection inputs. Confirm the motion ratio explicitly if the design began with the longer 20 mm-lead model.

PCG3232 catalog dimensions and ratings

PCG3232 rolled catalog row, PDF page 6
Parameter Reference Unit
Shaft d 31 mm
Lead I 32 mm/rev
Ball diameter Da 3.969 mm
Circuits n 2 count
Basic dynamic rating Ca 10580 N
Basic static rating Coa 20260 N
Nut body D 62 mm
Nut length L 60 mm
B 25 mm
Mounting thread A M56x1.5 metric thread

Dimensions retain the source symbols and printed precision. I denotes lead, Da ball diameter and n the source number of circuits. Ca and Coa are basic dynamic and static ratings in newtons. Do not treat either rating as an allowable payload or a complete life calculation.

Compare PCG3232 with PCG3220

Verified catalog comparison; dimensions in mm; lead I in mm/rev; A may be a metric thread designation
Field PCG3232 PCG3220
d 31 31
I 32 20
D 62 62
L 60 95
A M56x1.5 M56x1.5

The comparison uses separately verified catalog rows. Matching dimensions support an initial envelope review only. Different leads change travel per screw revolution, while the required rotational speed still depends on the target linear speed. Neither the table nor the model name establishes accuracy grade, preload or supplied configuration.

Installation and inquiry checklist

For this PCG nut, A = M56x1.5 is the mounting-thread designation, not a flange diameter. Review it together with B = 25 mm, D = 62 mm and L = 60 mm. Confirm mating-thread tolerance, engagement, shoulder seating and locking method on the assembly drawing.

  • Identify PCG3232, rolled process, quantity, working stroke and overall screw length. Attach the screw-end and nut-housing drawings.
  • Provide axial force through the complete cycle, travel speed, acceleration, mounting orientation and required life. Review buckling and critical speed for the actual unsupported span.
  • State positioning requirements, acceptable axial play, lubrication access and environmental protection. Confirm offered preload, accuracy and inspection conditions with engineering.

Allow for support bearings, end clearances and maintenance access beyond the listed nut length. Confirm the offered assembly and drawing revision before committing the machine layout.

Questions about PCG3232

Does PCG3232 specify the complete screw length?

No. The catalog lists L = 60 mm for the nut. Working stroke, screw length, end machining and support locations must be specified separately.

Can PCG3232 replace PCG3220 without a drawing check?

No. The comparison preserves each row’s d, lead, D, L and A values. Confirm the full mounting interface, shaft ends, load cycle and motion requirements; the catalog does not establish interchangeability.

What does the PCG3232 load table establish?

The source lists Ca = 10580 N and Coa = 20260 N as basic ratings. They are not permissible machine loads. Confirm the rating basis, duty cycle, life target and safety checks before selection.

Source and engineering confirmation

See the original ball screw catalog, PDF page 6 (printed page 5); the PCG header and drawing are on PDF page 5. These are catalog reference values. Engineering must confirm the exact offered dimensions, configuration and controlled drawing. The historical section title does not establish current stock, price or delivery.

Send the model and duty details through the PCG3232 configuration inquiry.

Custom requirements

Need help selecting a model or configuration?

Catalog reference only. Confirm the offered assembly, controlled drawing, duty cycle and commercial terms.

Discuss your application
Product inquiry

Request a quote or engineering review