Products

Home›Products

PFI2525 Rolled Ball Screw
Ball Screw Catalog Models

PFI2525 Rolled Ball Screw

Series / Model PFI2525

Review PFI2525 rolled ball screw dimensions, 25 mm lead and 47 mm nut length. Compare the PFI flange envelope and request a configuration drawing.

Product information

Overview

PFI2525 is a PFI flanged-nut reference in the rolled section of the Series Motion ball screw catalog. Its source row lists d = 24.1 mm and I = 25 mm per revolution. Use this page to compare the mounting envelope and prepare a drawing-based configuration inquiry.

Separate the 25 mm lead from the compact axial envelope

PFI2525 lists a 25 mm lead with a 47 mm nut length and two circuits. PFI2510 is longer at 85 mm and has four circuits. PFI2525 also has a different body diameter and flange callouts. Compare the entire row, not only the larger lead, when checking travel per revolution and available housing space.

PFI2525 dimensions and basic ratings

PFI2525 rolled reference, catalog PDF page 9; units shown for each field
Parameter Reference Unit
Shaft callout d 24.1 mm
Lead I 25 mm/rev
Ball diameter Da 3.5 mm
Number of circuits n 2 count
Basic dynamic rating Ca 7900 N
Basic static rating Coa 13690 N
Nut body callout D 42 mm
Flange callout A 70 mm
Drawing callout B 12 mm
Nut length L 47 mm
Drawing callout W 55 mm

Values retain the printed precision and source symbols. The circuit count n is dimensionless; it is not a thread-start count. Drawing callouts A, B and W belong to the PFI flange geometry, not a nut mounting-thread designation. Check the original drawing on PDF page 9 for the callout positions. Hole details and the offered flange form must be confirmed on the controlled drawing rather than inferred from this table.

Compare PFI2525 with PFI2510

PFI catalog comparison: d, D, A, B, L and W in mm; I in mm/rev
Field PFI2525 PFI2510
d 24.1 24.5
I 25 10
D 42 46
A 70 72
B 12 12
L 47 85
W 55 58

Use the complete selected row. Shared dimensions do not establish interchangeability, equivalent preload, accuracy or load performance. Check the nut seat, flange retention, shaft-end geometry and lubrication access together before replacing an assembly or releasing a new design.

Information needed for configuration review

  • Specify PFI2525, rolled process, quantity, required working stroke and overall screw length. Include the mating flange, nut-housing and shaft-end drawings.
  • Provide the axial load through each movement, speed, acceleration, mounting direction, cycles per hour and required service life. State the support arrangement and unsupported screw length.
  • Identify positioning requirements, permitted axial play, lubrication access and environmental conditions. Request the offered accuracy, preload, inspection basis and drawing revision in the quotation.

Catalog inclusion is not confirmation of current stock or an approved application. Confirm the offered configuration, availability and delivery before finalizing the machine layout. Basic ratings are not a substitute for an application-specific selection calculation.

Questions about PFI2525

Is PFI2525 a rolled or ground catalog reference?

This PFI2525 row appears in the Stock Rolled Ball Screw section, on PDF page 9. The PFI prefix is a family label; do not infer process or accuracy from the prefix alone. Confirm the offered process and accuracy on the configuration drawing and quotation.

Does L = 47 mm specify the working stroke?

No. L = 47 mm is the catalog nut length. Required stroke, overall screw length, shaft-end machining and support positions must be supplied separately.

Can the PFI2525 basic ratings be used as the machine working load?

Not directly. Ca = 7900 N and Coa = 13690 N are the printed basic dynamic and static ratings. Selection requires the load cycle, rating basis, target life and separate static, buckling and speed checks.

Check the source and request a drawing

Read the original PFI2525 catalog row and the PFI drawing and field definitions on PDF page 9. The 25 mm size table provides other catalog references. Send a PFI2525 rolled configuration inquiry with the application cycle and mounting requirements.

Custom requirements

Need help selecting a model or configuration?

Discuss your application
Product inquiry

Request a quote or engineering review