Products

Home›Products

PFI3205 Rolled Ball Screw
Ball Screw Catalog Models

PFI3205 Rolled Ball Screw

Series / Model PFI3205

Review PFI3205 rolled ball screw dimensions, 5 mm lead and 52 mm nut length. Compare the PFI flange envelope and request a configuration drawing.

Product information

Overview

PFI3205 is a PFI flanged-nut reference in the rolled section of the Series Motion ball screw catalog. Its source row lists d = 31.6 mm and I = 5 mm per revolution. Use this page to compare the mounting envelope and prepare a drawing-based configuration inquiry.

Start the 5 mm-lead comparison from the smaller flange envelope

PFI3205 uses D = 46 mm, A = 72 mm and L = 52 mm. These dimensions are smaller than the PFI3210 row, which has a 90 mm nut length. The printed shaft callout is 31.6 mm. Preserve that value and check the actual shaft ends rather than treating all 32-series screws as geometrically identical.

PFI3205 dimensions and basic ratings

PFI3205 rolled reference, catalog PDF page 9; units shown for each field
Parameter Reference Unit
Shaft callout d 31.6 mm
Lead I 5 mm/rev
Ball diameter Da 3.5 mm
Number of circuits n 4 count
Basic dynamic rating Ca 17080 N
Basic static rating Coa 37420 N
Nut body callout D 46 mm
Flange callout A 72 mm
Drawing callout B 12 mm
Nut length L 52 mm
Drawing callout W 58 mm

Values retain the printed precision and source symbols. The circuit count n is dimensionless; it is not a thread-start count. Drawing callouts A, B and W belong to the PFI flange geometry, not a nut mounting-thread designation. Check the original drawing on PDF page 9 for the callout positions. Hole details and the offered flange form must be confirmed on the controlled drawing rather than inferred from this table.

Compare PFI3205 with PFI3210

PFI catalog comparison: d, D, A, B, L and W in mm; I in mm/rev
Field PFI3205 PFI3210
d 31.6 32
I 5 10
D 46 54
A 72 88
B 12 15
L 52 90
W 58 70

Use the complete selected row. Shared dimensions do not establish interchangeability, equivalent preload, accuracy or load performance. Check the nut seat, flange retention, shaft-end geometry and lubrication access together before replacing an assembly or releasing a new design.

Information needed for configuration review

  • Specify PFI3205, rolled process, quantity, required working stroke and overall screw length. Include the mating flange, nut-housing and shaft-end drawings.
  • Provide the axial load through each movement, speed, acceleration, mounting direction, cycles per hour and required service life. State the support arrangement and unsupported screw length.
  • Identify positioning requirements, permitted axial play, lubrication access and environmental conditions. Request the offered accuracy, preload, inspection basis and drawing revision in the quotation.

Catalog inclusion is not confirmation of current stock or an approved application. Confirm the offered configuration, availability and delivery before finalizing the machine layout. Basic ratings are not a substitute for an application-specific selection calculation.

Questions about PFI3205

Is PFI3205 a rolled or ground catalog reference?

This PFI3205 row appears in the Stock Rolled Ball Screw section, on PDF page 9. The PFI prefix is a family label; do not infer process or accuracy from the prefix alone. Confirm the offered process and accuracy on the configuration drawing and quotation.

Does L = 52 mm specify the working stroke?

No. L = 52 mm is the catalog nut length. Required stroke, overall screw length, shaft-end machining and support positions must be supplied separately.

Can the PFI3205 basic ratings be used as the machine working load?

Not directly. Ca = 17080 N and Coa = 37420 N are the printed basic dynamic and static ratings. Selection requires the load cycle, rating basis, target life and separate static, buckling and speed checks.

Check the source and request a drawing

Read the original PFI3205 catalog row and the PFI drawing and field definitions on PDF page 9. The 32 mm size table provides other catalog references. Send a PFI3205 rolled configuration inquiry with the application cycle and mounting requirements.

Custom requirements

Need help selecting a model or configuration?

Discuss your application
Product inquiry

Request a quote or engineering review