Products

Home›Products

PFI3220 Rolled Ball Screw
Ball Screw Catalog Models

PFI3220 Rolled Ball Screw

Series / Model PFI3220

Review PFI3220 rolled ball screw dimensions, 20 mm lead and 90 mm nut length. Compare the PFI flange envelope and request a configuration drawing.

Product information

Overview

PFI3220 is a PFI flanged-nut reference in the rolled section of the Series Motion ball screw catalog. Its source row lists d = 31 mm and I = 20 mm per revolution. Use this page to compare the mounting envelope and prepare a drawing-based configuration inquiry.

Review the longer four-circuit option against PFI3232

PFI3220 and PFI3232 share d = 31 mm, Da = 3.969 mm and the listed D, A, B and W dimensions. PFI3220 has a 20 mm lead, four circuits and a 90 mm nut length; PFI3232 has a 32 mm lead, two circuits and a 58 mm nut length. The housing face may look similar while the axial package and ratings change.

PFI3220 dimensions and basic ratings

PFI3220 rolled reference, catalog PDF page 9; units shown for each field
Parameter Reference Unit
Shaft callout d 31 mm
Lead I 20 mm/rev
Ball diameter Da 3.969 mm
Number of circuits n 4 count
Basic dynamic rating Ca 19390 N
Basic static rating Coa 39980 N
Nut body callout D 52 mm
Flange callout A 87 mm
Drawing callout B 15 mm
Nut length L 90 mm
Drawing callout W 67 mm

Values retain the printed precision and source symbols. The circuit count n is dimensionless; it is not a thread-start count. Drawing callouts A, B and W belong to the PFI flange geometry, not a nut mounting-thread designation. Check the original drawing on PDF page 9 for the callout positions. Hole details and the offered flange form must be confirmed on the controlled drawing rather than inferred from this table.

Compare PFI3220 with PFI3232

PFI catalog comparison: d, D, A, B, L and W in mm; I in mm/rev
Field PFI3220 PFI3232
d 31 31
I 20 32
D 52 52
A 87 87
B 15 15
L 90 58
W 67 67

Use the complete selected row. Shared dimensions do not establish interchangeability, equivalent preload, accuracy or load performance. Check the nut seat, flange retention, shaft-end geometry and lubrication access together before replacing an assembly or releasing a new design.

Information needed for configuration review

  • Specify PFI3220, rolled process, quantity, required working stroke and overall screw length. Include the mating flange, nut-housing and shaft-end drawings.
  • Provide the axial load through each movement, speed, acceleration, mounting direction, cycles per hour and required service life. State the support arrangement and unsupported screw length.
  • Identify positioning requirements, permitted axial play, lubrication access and environmental conditions. Request the offered accuracy, preload, inspection basis and drawing revision in the quotation.

Catalog inclusion is not confirmation of current stock or an approved application. Confirm the offered configuration, availability and delivery before finalizing the machine layout. Basic ratings are not a substitute for an application-specific selection calculation.

Questions about PFI3220

Is PFI3220 a rolled or ground catalog reference?

This PFI3220 row appears in the Stock Rolled Ball Screw section, on PDF page 9. The PFI prefix is a family label; do not infer process or accuracy from the prefix alone. Confirm the offered process and accuracy on the configuration drawing and quotation.

Does L = 90 mm specify the working stroke?

No. L = 90 mm is the catalog nut length. Required stroke, overall screw length, shaft-end machining and support positions must be supplied separately.

Can the PFI3220 basic ratings be used as the machine working load?

Not directly. Ca = 19390 N and Coa = 39980 N are the printed basic dynamic and static ratings. Selection requires the load cycle, rating basis, target life and separate static, buckling and speed checks.

Check the source and request a drawing

Read the original PFI3220 catalog row and the PFI drawing and field definitions on PDF page 9. The 32 mm size table provides other catalog references. Send a PFI3220 rolled configuration inquiry with the application cycle and mounting requirements.

Custom requirements

Need help selecting a model or configuration?

Discuss your application
Product inquiry

Request a quote or engineering review