PFI4005 Rolled Ball Screw
Series / Model PFI4005
Review PFI4005 rolled ball screw dimensions, 5 mm lead and 55 mm nut length. Compare the PFI flange envelope and request a configuration drawing.
Overview
PFI4005 is a PFI flanged-nut reference in the rolled section of the Series Motion ball screw catalog. Its source row lists d = 39.58 mm and I = 5 mm per revolution. Use this page to compare the mounting envelope and prepare a drawing-based configuration inquiry.
Preserve the two-decimal shaft reference
PFI4005 prints d = 39.58 mm. Do not round this to 40 mm or borrow the 39.51 mm value of PFI4010. The 5 mm-lead row also has a 55 mm nut length and a smaller flange envelope than PFI4010. Both the shaft-end drawing and the mating housing must be checked for a change of model.
PFI4005 dimensions and basic ratings
| Parameter | Reference | Unit |
|---|---|---|
| Shaft callout d | 39.58 | mm |
| Lead I | 5 | mm/rev |
| Ball diameter Da | 3.5 | mm |
| Number of circuits n | 4 | count |
| Basic dynamic rating Ca | 18890 | N |
| Basic static rating Coa | 47560 | N |
| Nut body callout D | 56 | mm |
| Flange callout A | 90 | mm |
| Drawing callout B | 15 | mm |
| Nut length L | 55 | mm |
| Drawing callout W | 72 | mm |
Values retain the printed precision and source symbols. The circuit count n is dimensionless; it is not a thread-start count. Drawing callouts A, B and W belong to the PFI flange geometry, not a nut mounting-thread designation. Check the original drawing on PDF page 9 for the callout positions. Hole details and the offered flange form must be confirmed on the controlled drawing rather than inferred from this table.
Compare PFI4005 with PFI4010
| Field | PFI4005 | PFI4010 |
|---|---|---|
| d | 39.58 | 39.51 |
| I | 5 | 10 |
| D | 56 | 62 |
| A | 90 | 104 |
| B | 15 | 18 |
| L | 55 | 93 |
| W | 72 | 82 |
Use the complete selected row. Shared dimensions do not establish interchangeability, equivalent preload, accuracy or load performance. Check the nut seat, flange retention, shaft-end geometry and lubrication access together before replacing an assembly or releasing a new design.
Information needed for configuration review
- Specify PFI4005, rolled process, quantity, required working stroke and overall screw length. Include the mating flange, nut-housing and shaft-end drawings.
- Provide the axial load through each movement, speed, acceleration, mounting direction, cycles per hour and required service life. State the support arrangement and unsupported screw length.
- Identify positioning requirements, permitted axial play, lubrication access and environmental conditions. Request the offered accuracy, preload, inspection basis and drawing revision in the quotation.
Catalog inclusion is not confirmation of current stock or an approved application. Confirm the offered configuration, availability and delivery before finalizing the machine layout. Basic ratings are not a substitute for an application-specific selection calculation.
Questions about PFI4005
Is PFI4005 a rolled or ground catalog reference?
This PFI4005 row appears in the Stock Rolled Ball Screw section, on PDF page 10. The PFI prefix is a family label; do not infer process or accuracy from the prefix alone. Confirm the offered process and accuracy on the configuration drawing and quotation.
Does L = 55 mm specify the working stroke?
No. L = 55 mm is the catalog nut length. Required stroke, overall screw length, shaft-end machining and support positions must be supplied separately.
Can the PFI4005 basic ratings be used as the machine working load?
Not directly. Ca = 18890 N and Coa = 47560 N are the printed basic dynamic and static ratings. Selection requires the load cycle, rating basis, target life and separate static, buckling and speed checks.
Check the source and request a drawing
Read the original PFI4005 catalog row and the PFI drawing and field definitions on PDF page 9. The 40 mm size table provides other catalog references. Send a PFI4005 rolled configuration inquiry with the application cycle and mounting requirements.
