Products

Home›Products

PFI4010 Rolled Ball Screw
Ball Screw Catalog Models

PFI4010 Rolled Ball Screw

Series / Model PFI4010

Review PFI4010 rolled ball screw dimensions, 10 mm lead and 93 mm nut length. Compare the PFI flange envelope and request a configuration drawing.

Product information

Overview

PFI4010 is a PFI flanged-nut reference in the rolled section of the Series Motion ball screw catalog. Its source row lists d = 39.51 mm and I = 10 mm per revolution. Use this page to compare the mounting envelope and prepare a drawing-based configuration inquiry.

Check the wider flange and 93 mm nut length

PFI4010 combines a 10 mm lead with D = 62 mm, A = 104 mm and L = 93 mm. These do not match the PFI4005 interface. The 39.51 mm shaft callout must remain attached to this row, together with its 7.144 mm ball diameter and four-circuit notation.

PFI4010 dimensions and basic ratings

PFI4010 rolled reference, catalog PDF page 10; units shown for each field
Parameter Reference Unit
Shaft callout d 39.51 mm
Lead I 10 mm/rev
Ball diameter Da 7.144 mm
Number of circuits n 4 count
Basic dynamic rating Ca 47420 N
Basic static rating Coa 89720 N
Nut body callout D 62 mm
Flange callout A 104 mm
Drawing callout B 18 mm
Nut length L 93 mm
Drawing callout W 82 mm

Values retain the printed precision and source symbols. The circuit count n is dimensionless; it is not a thread-start count. Drawing callouts A, B and W belong to the PFI flange geometry, not a nut mounting-thread designation. Check the original drawing on PDF page 9 for the callout positions. Hole details and the offered flange form must be confirmed on the controlled drawing rather than inferred from this table.

Compare PFI4010 with PFI4005

PFI catalog comparison: d, D, A, B, L and W in mm; I in mm/rev
Field PFI4010 PFI4005
d 39.51 39.58
I 10 5
D 62 56
A 104 90
B 18 15
L 93 55
W 82 72

Use the complete selected row. Shared dimensions do not establish interchangeability, equivalent preload, accuracy or load performance. Check the nut seat, flange retention, shaft-end geometry and lubrication access together before replacing an assembly or releasing a new design.

Information needed for configuration review

  • Specify PFI4010, rolled process, quantity, required working stroke and overall screw length. Include the mating flange, nut-housing and shaft-end drawings.
  • Provide the axial load through each movement, speed, acceleration, mounting direction, cycles per hour and required service life. State the support arrangement and unsupported screw length.
  • Identify positioning requirements, permitted axial play, lubrication access and environmental conditions. Request the offered accuracy, preload, inspection basis and drawing revision in the quotation.

Catalog inclusion is not confirmation of current stock or an approved application. Confirm the offered configuration, availability and delivery before finalizing the machine layout. Basic ratings are not a substitute for an application-specific selection calculation.

Questions about PFI4010

Is PFI4010 a rolled or ground catalog reference?

This PFI4010 row appears in the Stock Rolled Ball Screw section, on PDF page 10. The PFI prefix is a family label; do not infer process or accuracy from the prefix alone. Confirm the offered process and accuracy on the configuration drawing and quotation.

Does L = 93 mm specify the working stroke?

No. L = 93 mm is the catalog nut length. Required stroke, overall screw length, shaft-end machining and support positions must be supplied separately.

Can the PFI4010 basic ratings be used as the machine working load?

Not directly. Ca = 47420 N and Coa = 89720 N are the printed basic dynamic and static ratings. Selection requires the load cycle, rating basis, target life and separate static, buckling and speed checks.

Check the source and request a drawing

Read the original PFI4010 catalog row and the PFI drawing and field definitions on PDF page 9. The 40 mm size table provides other catalog references. Send a PFI4010 rolled configuration inquiry with the application cycle and mounting requirements.

Custom requirements

Need help selecting a model or configuration?

Discuss your application
Product inquiry

Request a quote or engineering review