Products

Home›Products

PFI5040 Rolled Ball Screw
Ball Screw Catalog Models

PFI5040 Rolled Ball Screw

Series / Model PFI5040

Review PFI5040 rolled ball screw dimensions, 40 mm lead and 71 mm nut length. Compare the PFI flange envelope and request a configuration drawing.

Product information

Overview

PFI5040 is a PFI flanged-nut reference in the rolled section of the Series Motion ball screw catalog. Its source row lists d = 48 mm and I = 40 mm per revolution. Use this page to compare the mounting envelope and prepare a drawing-based configuration inquiry.

Check the 71 mm nut with the shared flange callouts

The PFI5040 row pairs a 40 mm lead with a 71 mm nut length and two circuits. PFI5020 has the same listed body and flange envelope but is 93 mm long. This can change axial packaging, while the complete duty cycle and separate speed and load checks remain necessary for selection.

PFI5040 dimensions and basic ratings

PFI5040 rolled reference, catalog PDF page 10; units shown for each field
Parameter Reference Unit
Shaft callout d 48 mm
Lead I 40 mm/rev
Ball diameter Da 6.5 mm
Number of circuits n 2 count
Basic dynamic rating Ca 25050 N
Basic static rating Coa 50540 N
Nut body callout D 77 mm
Flange callout A 119 mm
Drawing callout B 18 mm
Nut length L 71 mm
Drawing callout W 94 mm

Values retain the printed precision and source symbols. The circuit count n is dimensionless; it is not a thread-start count. Drawing callouts A, B and W belong to the PFI flange geometry, not a nut mounting-thread designation. Check the original drawing on PDF page 9 for the callout positions. Hole details and the offered flange form must be confirmed on the controlled drawing rather than inferred from this table.

Compare PFI5040 with PFI5020

PFI catalog comparison: d, D, A, B, L and W in mm; I in mm/rev
Field PFI5040 PFI5020
d 48 48.15
I 40 20
D 77 77
A 119 119
B 18 18
L 71 93
W 94 94

Use the complete selected row. Shared dimensions do not establish interchangeability, equivalent preload, accuracy or load performance. Check the nut seat, flange retention, shaft-end geometry and lubrication access together before replacing an assembly or releasing a new design.

Information needed for configuration review

  • Specify PFI5040, rolled process, quantity, required working stroke and overall screw length. Include the mating flange, nut-housing and shaft-end drawings.
  • Provide the axial load through each movement, speed, acceleration, mounting direction, cycles per hour and required service life. State the support arrangement and unsupported screw length.
  • Identify positioning requirements, permitted axial play, lubrication access and environmental conditions. Request the offered accuracy, preload, inspection basis and drawing revision in the quotation.

Catalog inclusion is not confirmation of current stock or an approved application. Confirm the offered configuration, availability and delivery before finalizing the machine layout. Basic ratings are not a substitute for an application-specific selection calculation.

Questions about PFI5040

Is PFI5040 a rolled or ground catalog reference?

This PFI5040 row appears in the Stock Rolled Ball Screw section, on PDF page 10. The PFI prefix is a family label; do not infer process or accuracy from the prefix alone. Confirm the offered process and accuracy on the configuration drawing and quotation.

Does L = 71 mm specify the working stroke?

No. L = 71 mm is the catalog nut length. Required stroke, overall screw length, shaft-end machining and support positions must be supplied separately.

Can the PFI5040 basic ratings be used as the machine working load?

Not directly. Ca = 25050 N and Coa = 50540 N are the printed basic dynamic and static ratings. Selection requires the load cycle, rating basis, target life and separate static, buckling and speed checks.

Check the source and request a drawing

Read the original PFI5040 catalog row and the PFI drawing and field definitions on PDF page 9. The 50 mm size table provides other catalog references. Send a PFI5040 rolled configuration inquiry with the application cycle and mounting requirements.

Custom requirements

Need help selecting a model or configuration?

Discuss your application
Product inquiry

Request a quote or engineering review