Products

Home›Products

PFU2020 Rolled Ball Screw
Ball Screw Catalog Models

PFU2020 Rolled Ball Screw

Series / Model PFU2020

Review PFU2020 rolled ball screw dimensions: 19.4 mm shaft, 20 mm lead and 49 mm nut length. Compare mounting details and request engineering confirmation.

Product information

Overview

PFU2020 is a PFU reference in the catalog’s Stock Rolled Ball Screw section. Its row lists d = 19.4 mm, a 20 mm lead and L = 49 mm. Use this page to review the model’s geometry and prepare a configuration inquiry.

Use the 20 mm lead with its own load row

PFU2020 shares D, A, B, W, H and X with PFU2010, but L decreases from 54 to 49 mm and the source lists two circuits. The printed d changes from 19.3 to 19.4 mm. Retain the complete row when comparing package size, rather than combining the larger lead with another model’s basic ratings.

PFU2020 catalog dimensions and ratings

PFU2020 rolled catalog row, PDF page 4
Parameter Reference Unit
Shaft d 19.4 mm
Lead I 20 mm/rev
Ball diameter Da 3.5 mm
Circuits n 2 count
Basic dynamic rating Ca 7110 N
Basic static rating Coa 10940 N
Nut body D 36 mm
Flange A 57 mm
B 10 mm
Nut length L 49 mm
W 46 mm
H 48 mm
Hole diameter X 6.6 mm

Dimensions retain the source symbols and printed precision. I denotes lead, Da ball diameter and n the source number of circuits. Ca and Coa are basic dynamic and static ratings in newtons. Do not treat either rating as an allowable payload or a complete life calculation.

Compare PFU2020 with PFU2010

Verified catalog comparison; dimensions in mm; lead I in mm/rev; A may be a metric thread designation
Field PFU2020 PFU2010
d 19.4 19.3
I 20 10
D 36 36
L 49 54
A 57 57

The comparison uses separately verified catalog rows. Matching dimensions support an initial envelope review only. Different leads change travel per screw revolution, while the required rotational speed still depends on the target linear speed. Neither the table nor the model name establishes accuracy grade, preload or supplied configuration.

Installation and inquiry checklist

For the PFU flange, review A = 57 mm, W = 46 mm, H = 48 mm and X = 6.6 mm together. Confirm the applicable hole arrangement, angular orientation and bolt access against the controlled drawing. The family illustration is not a model-specific manufacturing drawing.

  • Identify PFU2020, rolled process, quantity, working stroke and overall screw length. Attach the screw-end and nut-housing drawings.
  • Provide axial force through the complete cycle, travel speed, acceleration, mounting orientation and required life. Review buckling and critical speed for the actual unsupported span.
  • State positioning requirements, acceptable axial play, lubrication access and environmental protection. Confirm offered preload, accuracy and inspection conditions with engineering.

Allow for support bearings, end clearances and maintenance access beyond the listed nut length. Confirm the offered assembly and drawing revision before committing the machine layout.

Questions about PFU2020

Does PFU2020 specify the complete screw length?

No. The catalog lists L = 49 mm for the nut. Working stroke, screw length, end machining and support locations must be specified separately.

Can PFU2020 replace PFU2010 without a drawing check?

No. The comparison preserves each row’s d, lead, D, L and A values. Confirm the full mounting interface, shaft ends, load cycle and motion requirements; the catalog does not establish interchangeability.

What does the PFU2020 load table establish?

The source lists Ca = 7110 N and Coa = 10940 N as basic ratings. They are not permissible machine loads. Confirm the rating basis, duty cycle, life target and safety checks before selection.

Source and engineering confirmation

See the original ball screw catalog, PDF page 4 (printed page 3); the PFU header and drawing are on PDF page 3. These are catalog reference values. Engineering must confirm the exact offered dimensions, configuration and controlled drawing. The historical section title does not establish current stock, price or delivery.

Send the model and duty details through the PFU2020 configuration inquiry.

Custom requirements

Need help selecting a model or configuration?

Catalog reference only. Confirm the offered assembly, controlled drawing, duty cycle and commercial terms.

Discuss your application
Product inquiry

Request a quote or engineering review