Products

Home›Products

PFU4010 Rolled Ball Screw
Ball Screw Catalog Models

PFU4010 Rolled Ball Screw

Series / Model PFU4010

Review PFU4010 rolled ball screw dimensions: 39.5 mm shaft, 10 mm lead and 93 mm nut length. Compare mounting details and request engineering confirmation.

Product information

Overview

PFU4010 is a PFU reference in the catalog’s Stock Rolled Ball Screw section. Its row lists d = 39.5 mm, a 10 mm lead and L = 93 mm. Use this page to review the model’s geometry and prepare a configuration inquiry.

Keep the larger-ball row separate

PFU4010 lists 7.144 mm balls, compared with 3.5 mm for PFU4005. Both use four circuits and the same listed flange dimensions, but L increases from 55 to 93 mm. Ask for the selected model and controlled assembly drawing explicitly when a design has room for either envelope.

PFU4010 catalog dimensions and ratings

PFU4010 rolled catalog row, PDF page 4
Parameter Reference Unit
Shaft d 39.5 mm
Lead I 10 mm/rev
Ball diameter Da 7.144 mm
Circuits n 4 count
Basic dynamic rating Ca 47420 N
Basic static rating Coa 89720 N
Nut body D 63 mm
Flange A 93 mm
B 14 mm
Nut length L 93 mm
W 78 mm
H 70 mm
Hole diameter X 9 mm

Dimensions retain the source symbols and printed precision. I denotes lead, Da ball diameter and n the source number of circuits. Ca and Coa are basic dynamic and static ratings in newtons. Do not treat either rating as an allowable payload or a complete life calculation.

Compare PFU4010 with PFU4005

Verified catalog comparison; dimensions in mm; lead I in mm/rev; A may be a metric thread designation
Field PFU4010 PFU4005
d 39.5 39.5
I 10 5
D 63 63
L 93 55
A 93 93

The comparison uses separately verified catalog rows. Matching dimensions support an initial envelope review only. Different leads change travel per screw revolution, while the required rotational speed still depends on the target linear speed. Neither the table nor the model name establishes accuracy grade, preload or supplied configuration.

Installation and inquiry checklist

For the PFU flange, review A = 93 mm, W = 78 mm, H = 70 mm and X = 9 mm together. Confirm the applicable hole arrangement, angular orientation and bolt access against the controlled drawing. The family illustration is not a model-specific manufacturing drawing.

  • Identify PFU4010, rolled process, quantity, working stroke and overall screw length. Attach the screw-end and nut-housing drawings.
  • Provide axial force through the complete cycle, travel speed, acceleration, mounting orientation and required life. Review buckling and critical speed for the actual unsupported span.
  • State positioning requirements, acceptable axial play, lubrication access and environmental protection. Confirm offered preload, accuracy and inspection conditions with engineering.

Allow for support bearings, end clearances and maintenance access beyond the listed nut length. Confirm the offered assembly and drawing revision before committing the machine layout.

Questions about PFU4010

Does PFU4010 specify the complete screw length?

No. The catalog lists L = 93 mm for the nut. Working stroke, screw length, end machining and support locations must be specified separately.

Can PFU4010 replace PFU4005 without a drawing check?

No. The comparison preserves each row’s d, lead, D, L and A values. Confirm the full mounting interface, shaft ends, load cycle and motion requirements; the catalog does not establish interchangeability.

What does the PFU4010 load table establish?

The source lists Ca = 47420 N and Coa = 89720 N as basic ratings. They are not permissible machine loads. Confirm the rating basis, duty cycle, life target and safety checks before selection.

Source and engineering confirmation

See the original ball screw catalog, PDF page 4 (printed page 3); the PFU header and drawing are on PDF page 3. These are catalog reference values. Engineering must confirm the exact offered dimensions, configuration and controlled drawing. The historical section title does not establish current stock, price or delivery.

Send the model and duty details through the PFU4010 configuration inquiry.

Custom requirements

Need help selecting a model or configuration?

Catalog reference only. Confirm the offered assembly, controlled drawing, duty cycle and commercial terms.

Discuss your application
Product inquiry

Request a quote or engineering review