Products

Home›Products

PFU5040 Rolled Ball Screw
Ball Screw Catalog Models

PFU5040 Rolled Ball Screw

Series / Model PFU5040

Review PFU5040 rolled ball screw dimensions: 48 mm shaft, 40 mm lead and 71 mm nut length. Compare mounting details and request engineering confirmation.

Product information

Overview

PFU5040 is a PFU reference in the catalog’s Stock Rolled Ball Screw section. Its row lists d = 48 mm, a 40 mm lead and L = 71 mm. Use this page to review the model’s geometry and prepare a configuration inquiry.

Check the 117 mm flange envelope

The largest lead in this 50-series group comes with A = 117 mm, B = 18 mm and H = 98 mm. PFU5010 and PFU5020 have smaller A and B dimensions but longer nuts. Review radial space and flange seating separately from the shorter L = 71 mm axial envelope.

PFU5040 catalog dimensions and ratings

PFU5040 rolled catalog row, PDF page 4
Parameter Reference Unit
Shaft d 48 mm
Lead I 40 mm/rev
Ball diameter Da 6.5 mm
Circuits n 2 count
Basic dynamic rating Ca 25050 N
Basic static rating Coa 50540 N
Nut body D 77 mm
Flange A 117 mm
B 18 mm
Nut length L 71 mm
W 94 mm
H 98 mm
Hole diameter X 11 mm

Dimensions retain the source symbols and printed precision. I denotes lead, Da ball diameter and n the source number of circuits. Ca and Coa are basic dynamic and static ratings in newtons. Do not treat either rating as an allowable payload or a complete life calculation.

Compare PFU5040 with PFU5020

Verified catalog comparison; dimensions in mm; lead I in mm/rev; A may be a metric thread designation
Field PFU5040 PFU5020
d 48 48.1
I 40 20
D 77 75
L 71 93
A 117 110

The comparison uses separately verified catalog rows. Matching dimensions support an initial envelope review only. Different leads change travel per screw revolution, while the required rotational speed still depends on the target linear speed. Neither the table nor the model name establishes accuracy grade, preload or supplied configuration.

Installation and inquiry checklist

For the PFU flange, review A = 117 mm, W = 94 mm, H = 98 mm and X = 11 mm together. Confirm the applicable hole arrangement, angular orientation and bolt access against the controlled drawing. The family illustration is not a model-specific manufacturing drawing.

  • Identify PFU5040, rolled process, quantity, working stroke and overall screw length. Attach the screw-end and nut-housing drawings.
  • Provide axial force through the complete cycle, travel speed, acceleration, mounting orientation and required life. Review buckling and critical speed for the actual unsupported span.
  • State positioning requirements, acceptable axial play, lubrication access and environmental protection. Confirm offered preload, accuracy and inspection conditions with engineering.

Allow for support bearings, end clearances and maintenance access beyond the listed nut length. Confirm the offered assembly and drawing revision before committing the machine layout.

Questions about PFU5040

Does PFU5040 specify the complete screw length?

No. The catalog lists L = 71 mm for the nut. Working stroke, screw length, end machining and support locations must be specified separately.

Can PFU5040 replace PFU5020 without a drawing check?

No. The comparison preserves each row’s d, lead, D, L and A values. Confirm the full mounting interface, shaft ends, load cycle and motion requirements; the catalog does not establish interchangeability.

What does the PFU5040 load table establish?

The source lists Ca = 25050 N and Coa = 50540 N as basic ratings. They are not permissible machine loads. Confirm the rating basis, duty cycle, life target and safety checks before selection.

Source and engineering confirmation

See the original ball screw catalog, PDF page 4 (printed page 3); the PFU header and drawing are on PDF page 3. These are catalog reference values. Engineering must confirm the exact offered dimensions, configuration and controlled drawing. The historical section title does not establish current stock, price or delivery.

Send the model and duty details through the PFU5040 configuration inquiry.

Custom requirements

Need help selecting a model or configuration?

Catalog reference only. Confirm the offered assembly, controlled drawing, duty cycle and commercial terms.

Discuss your application
Product inquiry

Request a quote or engineering review