Ball Spline Rotational Clearance and Preload: Specify the Reversal Test
November 4, 2026 · 6 min read
A ball spline’s response to reversing torque depends on its rotational clearance, rolling-contact condition and the stiffness of the surrounding assembly. Specifying “zero backlash” without a load, reference point and test method leaves the required behaviour unclear.
This guide separates clearance from elastic deflection and outlines an acceptance discussion for a matched spline shaft and nut. It does not assign a preload class to an SL or SO model. Use the application checklist to describe the complete operating requirement.
Separate clearance from deflection under load
Rotational clearance concerns relative freedom between the spline shaft and nut as the contact direction changes. Elastic deflection is movement under load caused by compliance in the contacts, shaft, supports and connected parts. Both can affect the measured response at the tool, but they are different quantities.
A small clearance specification does not mean the shaft and machine are infinitely stiff. Conversely, a displacement measured at a remote tool point does not identify spline clearance on its own. Establish which two components are being measured relative to one another and what torque is applied.
Check how the supplier expresses the clearance: as an angle, or as circumferential displacement at a specified reference. Preserve that definition and unit when comparing a drawing requirement with an inspection result.
Describe what preload is meant to achieve
Preload establishes an internal rolling-contact load before the external operating load is applied. An appropriate contact condition can reduce angular play and change the torque-displacement response. The required condition depends on the reversal duty, overhang, stiffness requirement and acceptable resistance to motion.
Request the proposed assembly’s specified clearance or preload condition and how it is verified. Class letters and terms such as “light” or “medium” belong to a defined product system; they are not a universal conversion between suppliers. A code is useful only with its corresponding definition and limits.
State the required outcome at the working point and ask the supplier to review the contact condition with the operating loads. Include any life-calculation treatment required for preload. Do not assume that selecting the strongest available preload automatically provides the best complete-axis result.
Keep housing fit and contact preload as separate specifications
The housing locates and restrains the nut. Its bore class and fastening arrangement are installation requirements. They do not define a verified internal contact preload for a matched spline pair.
Do not use a tighter housing fit or additional fastener tightening as an improvised method of removing angular play. Use the approved mounting and contact-condition specifications. If measured behaviour changes after the housing is secured, inspect the mounting arrangement and alignment before altering the spline specification. The installation guide covers those interface checks.
Define a reversal test before accepting a result
Agree the fixture and loading sequence with the supplier. The following fields make a proposed test reproducible; they are not a factory inspection procedure or universal pass/fail limits.
| Field | What to specify |
|---|---|
| Parts and support | Matched shaft/nut references, nut axial position, support span and restraint points. |
| Measurement | Relative components, instrument location, angular or linear unit and measurement radius if relevant. |
| Loading | Torque magnitude, both directions, loading/unloading sequence and any simultaneous external load. |
| Condition | Mounting state, lubrication, temperature and any agreed preparation sequence. |
| Acceptance | Quantity being assessed, allowed range, repeat checks and reporting method. |
Record the response as torque changes in both directions rather than reporting a single unexplained movement. Identify whether the reported quantity is reversal movement, clearance under a stated procedure, or loaded deflection. Keep those labels consistent in the drawing and inspection report.
Relate a linear indication to the measurement radius
Illustrative geometry: if a measurement arm has an assumed radius of 100 mm and its tangential displacement is 0.020 mm, the small-angle relation gives θ ≈ 0.020/100 = 0.00020 rad, approximately 0.0115°. The same angle produces a larger linear movement at a larger radius.
These assumed values are not an SL or SO clearance limit. A linear indicator result needs its measurement radius and reference geometry to be meaningful. The fixture, arm and supports can also deflect, so the conversion alone does not isolate the spline’s internal clearance.
Check the measurement chain when results differ
If an assembled machine shows more reversal movement than the component inspection, compare the two setups. Review couplings, shaft torsion, support bearings, tool overhang, nut mounting and the measurement reference. Separate observations made on the component from observations made at the complete machine’s working point.
Check more than one relevant nut position along the intended travel if the acceptance requirement calls for it. Record any position-dependent change instead of averaging it away. A replacement nut also needs confirmed compatibility with the shaft and its specified contact condition; matching the nominal diameter does not settle that question.
Download the reversal-test definition sheet (CSV). Keep the accepted condition with the drawing and use the combined-load and life review for the calculation assumptions.