Products

Home›Products

PFU1402 Rolled Ball Screw
Miniature Ball Screw

PFU1402 Rolled Ball Screw

Series / Model PFU1402

Review PFU1402 rolled ball screw data: 14 mm shaft, 2 mm lead and 23 mm nut length. Compare the exact row and mounting interfaces before quotation.

Product information

Overview

PFU1402 is listed in the Series Motion rolled PFU table with a 14 mm shaft and 2 mm lead. This page brings the exact source row together with mounting and configuration checks for an inquiry.

Check the 14 mm shaft without assuming a larger nut length

PFU1402 lists a 14 mm shaft, 2 mm lead and L = 23 mm. Compared with rolled PFU1202, the shaft is larger but the listed nut is shorter: PFU1202 uses d = 12 mm and L = 28 mm. The flange A changes from 37 to 40 mm and X from 4.5 to 5.5 mm.

A larger shaft diameter does not imply that every dimension increases. Use the separate nut envelope, flange pattern and shaft-end requirements to review the installation. The relatively short L reference does not establish the allowable stroke or make the assembly interchangeable with the smaller-diameter row.

Published rolled catalog reference

PFU1402 rolled PFU dimensions and ratings
Reference field Value Unit or notation
Shaft diameter d 14 mm
Lead I 2 mm/rev
Ball diameter Da 1.2 mm
Circuit notation n 4 catalog notation
Basic dynamic load rating Ca 2200 N
Basic static load rating Coa 5700 N
Nut body D 21 mm
Flange A 40 mm
Dimension B 6 mm
Nut length L 23 mm
Dimension W 31 mm
Dimension H 26 mm
Dimension X 5.5 mm

The values above agree between the published rolled-family HTML row and physical page 4 of the company Ball Screw catalog (printed Ball Screw-3). Keep the source drawing with the dimensional letters. Ca and Coa are catalog basic load ratings in N, not recommended working loads or a simultaneous operating envelope.

Keep the process and complete assembly explicit

PFU identifies a nut configuration; it does not by itself establish rolled versus ground manufacture, an accuracy grade or a supplied preload. This reference uses the rolled table specifically. Preserve any suffix and distinguish the screw lead from ball-circuit notation when preparing the order description.

Review shaft ends, supports, nut mounting and the moving envelope together. Include the whole load and motion cycle rather than a single maximum speed or force. Lubrication, environmental protection and acceptance measurements should be agreed for the offered assembly. Catalog inclusion does not confirm current stock, price or delivery time.

Questions about PFU1402

What distinguishes the PFU1402 reference?

PFU1402 lists a 14 mm shaft, 2 mm lead and L = 23 mm. Compared with rolled PFU1202, the shaft is larger but the listed nut is shorter: PFU1202 uses d = 12 mm and L = 28 mm. The flange A changes from 37 to 40 mm and X from 4.5 to 5.5 mm.

Does the PFU1402 row specify travel accuracy or preload?

The dimensions and load ratings do not assign a complete accuracy or preload configuration. State the required positioning accuracy, axial play or preload and inspection conditions, then confirm the offered assembly designation and drawing.

Is L = 23 mm the PFU1402 working stroke?

No. L is the nut-length dimension. Working stroke, total shaft length, end machining, bearing supports and end clearances need their own assembly drawing.

What information is required for a PFU1402 quotation?

Include the exact rolled model and any suffix, quantity, shaft length and end drawing, usable stroke, nut mounting layout, support arrangement, load and speed cycle, lubrication, environment and accuracy requirement. Ask for confirmation of the offered configuration and commercial terms.

Compare the source and send an inquiry

Open the rolled miniature ball screw family table and the PFU1202 Rolled Miniature Ball Screw reference. Send the exact model and installation drawing through the PFU1402 inquiry page for configuration review.

Custom requirements

Need help selecting a model or configuration?

This page is a catalog reference. Send the exact model, drawing and load cycle to confirm the offered configuration and commercial terms.

Discuss your application
Product inquiry

Request a quote or engineering review