Ball Spline Selection: Torque, Moment Loads and Application Checklist
November 4, 2026 · 6 min read
Ball spline selection starts with a sketch of the moving assembly and a record of the loads throughout its cycle. A torque value and a nominal shaft size leave out the radial load, overturning moment, support arrangement and sliding duty that can change the selection.
Use this guide to build an application sheet for an SL or SO ball spline. It separates application loads from catalogue ratings and shows what to confirm before selecting a size or replacing an assembly. Product dimensions remain on the SL series and SO series pages.
Draw what moves and where the loads enter
Mark the spline shaft axis, nut position, payload attachment, shaft supports and the component that drives axial travel. State whether the shaft rotates, the nut translates, or both motions occur. Mark the permitted relative rotation between shaft and nut and the required stroke endpoints.
A conventional ball spline permits axial sliding while transmitting torque or restraining relative rotation. Define the axial drive separately. The existing ball screw and ball spline comparison explains that functional distinction.
Place process forces and the centre of gravity on the sketch, with their distances from the spline and support references. If the payload extends beyond the nut, show the overhang at both ends of travel. Include any external guide: its presence changes which component supports each load.
Resolve gravity and axial holding separately
For a vertical or inclined installation, draw the weight vector against the shaft axis and identify its axial and transverse components. Retain the payload’s offset because the same weight can also create a bending moment. The ball spline’s ability to transmit torque does not provide a positive axial holding function; relative axial sliding remains an intended motion.
Show which machine elements drive, support and control the axial load during operation, stopped states, power loss and maintenance. Preload, seal drag or a sliding-resistance reading does not establish an approved load-holding capacity. Keep the nut-retention and shaft-location distinction explicit: retaining the nut body in its housing does not lock the sliding shaft to it.
Agree the actual machine’s required load-control and protective measures with the responsible integrator before commissioning. This spline-selection record does not specify a holding device, brake design or protective performance claim.
Keep torque, radial force and moment as separate inputs
Torque about the shaft axis, force perpendicular to it and a moment tending to tilt the nut describe different loading effects. Record their directions and points of application. Do not combine them into one number because the catalogue presents them in neighbouring columns.
Illustrative load sketch: suppose a transverse process force of 80 N acts at a perpendicular offset of 120 mm from the chosen support reference. Its moment about that reference is 80 × 0.120 = 9.6 N·m. If a separate drive applies 1.5 N·m about the shaft axis, record that torque separately. The 9.6 N·m moment and 1.5 N·m torque are not an 11.1 N·m spline requirement.
The moment above is calculated about the stated reference; it is not automatically the moment carried by one nut. Determine reactions from the complete support geometry. A shared force can produce different reactions when support spacing, nut spacing or payload position changes. This example provides application arithmetic, not a model recommendation.
Build a phase-by-phase load case
Record when the largest loads occur. A process load during a stationary dwell can differ from the load during rapid travel or reversal. Peak torque and peak bending moment may occur in different phases; identify any phase in which they act together.
| Phase | Motion to record | Load information | Additional condition |
|---|---|---|---|
| Travel | Start/end position, speed and acceleration | Torque, radial force and moment with directions | Payload position and active supports |
| Process or dwell | Stationary, rotating or sliding | Process force and its lever arm | Hold duration and force variation |
| Return and reversal | Deceleration, reversal and return speed | Changed load directions and transients | Cycles per minute and operating hours |
| Exceptional event | Stop or disturbance to assess | Known shock or emergency load case | Required review and machine procedure |
Also state stroke, overall shaft length, support span, moving mass, operating temperature, contamination and available lubrication access. A short stroke repeated frequently is a different duty description from occasional full-length travel, even if both have the same maximum speed.
Keep each rating with its model and definition
The SL/SO tables publish load ratings in kgf and torque or moment ratings in kgf·m. Those units differ from N and N·m. Keep the original table unit beside every rating you copy, and use a checked conversion when the application calculations use SI units.
Record the exact model row, whether a rating is dynamic or static, and the stated configuration. A static rating is not a substitute for a dynamic rating. A catalogue rating is also not a continuous operating limit that can be applied without reviewing the duty and the maker’s selection method.
For combined loading and service-life assessment, request the calculation method, rating basis, load factors and definitions of any moment columns used. Do not assume a moment column refers to one nut or a pair of nuts from its label alone. Select the assembly only after those definitions match the proposed support arrangement.
Resolve the mounting and clearance requirement
Choose the mounting interface from the machine drawing. SLF and SOF have flange interfaces; SLT and SOT have cylindrical bodies with keyways. Check available space, fastener or key access, axial retention and service access for the selected model. Use the housing fit and installation guide for the bore and assembly checks.
Read the actual shaft-diameter column rather than inferring a measurement from every size code. For example, SO nominal code 015 has a 13.6 mm shaft. A replacement review also needs the nut length, outside diameter, flange or keyway geometry, shaft raceway match and agreed clearance or preload. Matching one diameter does not establish interchangeability.
State the permitted rotational play or required torsional stiffness at a defined load and measurement point. Ask for the selected assembly’s clearance or preload specification and inspection method. A request for “zero backlash” needs that context, including reversal direction and the contribution of couplings, supports and the machine structure.
Send a complete selection sheet
- Drawing: motion sketch, shaft supports, nut positions, overhangs and reference dimensions.
- Duty: phase-by-phase loads, directions, stroke, speed, acceleration, dwell and operating schedule.
- Interfaces: nut type, shaft length, mounting details, end machining and parts that must fit an existing machine.
- Performance: permitted rotational clearance, stiffness requirement, target life and proposed acceptance method.
- Environment and scope: temperature, contamination, lubrication access, quantity and which matched parts are required.
Download the selection and load-case worksheet (CSV). Mark unknown inputs for review instead of filling them with assumed ratings. For a replacement, include the original designation, drawings and reason for replacement.